5 catalogued sizes, dimensioned to Trade series (closed-end blind rivet nuts). Pick any row and the technical drawing redraws to it.
Closed-End Round-Body Blind Rivet Nuts to Trade series (closed-end blind rivet nuts) are catalogued in sizes M4 to M10, with pitch 0.7-1.5 mm, head 9-17 mm. 5 sizes are held in the table below, and the technical drawing redraws to whichever row you select.
Standard
Trade series (closed-end blind rivet nuts)
Size range
M4-M10
Pitch
0.7-1.5 mm
Head
9-17 mm
Catalogued sizes
5
Dimensions are nominal values from the governing standard. Confirm the tolerance class for your application before ordering.
Applications & Industries
What Closed-End Round-Body Blind Rivet Nuts are specified for, industry by industry. Stocked from M4 to M10.
Industries that specify Closed-End Round-Body Blind Rivet Nuts
Outdoor enclosuresCover and bracket attachment points exposed to water and dirt.
HVAC fabricationPanel hardware installed after the duct or enclosure has been formed.
Refrigeration equipmentSealed threaded mounting points in formed panels and closed housings.
Vehicle bodyworkBlind threads in rails and box sections where the cavity must stay closed.
Automotive & transportVibration-prone joints where the locking type is specified on the drawing.
Maintenance & MROReplacements matched to the existing bolt class, thread and finish.
Typical applications
forming the blind bulb within the specified grip range
choosing steel, stainless steel or aluminum for the service environment
adding a sealed internal thread from the front face of a panel
keeping water and debris out of a closed section behind the insert
joints re-torqued at a service interval
completing a bolted joint on a stud, rod or bolt
Service conditions to specify against
Marine and coastal
Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.
High load
Supplied in ISO 898-1 property classes, so the joint can be designed to a stated proof load and tightened to a calculated torque rather than by feel.
Match the class
A nut below the bolt property class strips before the bolt reaches its own limit — pair class 8 nuts with 8.8 bolts, class 10 with 10.9.
Where to use something else
Do not drill to the thread minor diameter; the installation hole is set by the body and forming requirements.
Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.
Sends the selected values to the quote form below.
Request a Quotation for Closed-End Round-Body Blind Rivet Nuts
The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.
Dimensions & Specifications (Trade series (closed-end blind rivet nuts))
Every row below is a starting point for the customizer above — pick any size and the drawing will redraw to that row.
Manufactured to Trade series (closed-end blind rivet nuts), Closed-End Round-Body Blind Rivet Nuts are nuts supplied by Engineering Hardware. The dimensional data, materials and selection notes are summarized here.
What Are Closed-End Round-Body Blind Rivet Nuts?
Closed-End Round-Body Blind Rivet Nuts are nuts defined by Trade series (closed-end blind rivet nuts). They are selected by thread size and the dimensional characteristics shown below, and are available in a range of materials and finishes to suit the application and environment.
Materials & Finishes
Common materials include carbon steel (typically zinc plated or hot-dip galvanized), alloy steel in property classes 8.8, 10.9 and 12.9, and stainless steel A2 (304) or A4 (316) for corrosion resistance. Specify the material, property class and surface finish appropriate to your load and environment.
Pricing
Closed-End Round-Body Blind Rivet Nuts are supplied to order. Pricing starts from approximately US$0.12 per piece for standard sizes in carbon steel; final pricing depends on size, material, finish and order quantity (MOQ applies). Submit your exact configuration with the quote form above.
Inside the plant
Manufactured in our own plant
This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.
01
Cold heading
Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.
Head dimensions and under-head radius checked at set-up and per shift.
02
Thread rolling
Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.
Go / no-go ring gauges to ISO 965 tolerance class 6g.
03
Heat treatment
Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.
Core hardness and tensile tested per lot to ISO 898-1.
04
Surface treatment
Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.
Coating thickness and neutral salt spray hours to ISO 9227.
Frequently Asked Questions
What is the controlling standard for Closed-End Round-Body Blind Rivet Nuts?
Closed-End Round-Body Blind Rivet Nuts are manufactured to Trade series (closed-end blind rivet nuts). The dimensional values on this page follow that standard.
What sizes are available for Closed-End Round-Body Blind Rivet Nuts?
The table on this page lists 5 sizes for Closed-End Round-Body Blind Rivet Nuts, ranging from M4 to M10. Sizes outside the table can be quoted on request.
In which materials are Closed-End Round-Body Blind Rivet Nuts supplied?
Closed-End Round-Body Blind Rivet Nuts are supplied in matching property-class steel and stainless A2 / A4, with finishes including zinc plating, hot-dip galvanizing and black oxide. Choose material and finish to suit the load and the service environment for Closed-End Round-Body Blind Rivet Nuts.
How do I request a quotation?
Use the parametric drawing on this page to set the exact configuration (size, material, finish) and click "Request this configuration" — a specialist from Engineering Hardware will respond within one business day.
Need a fastener quote or a spec sheet?Message our engineers on WhatsApp — send a drawing or DIN number and get pricing back fast.Start WhatsApp Chat →
This website uses only necessary and functional cookies to operate, secure, and improve basic website performance.
We do not use advertising cookies, Google Analytics, or cross-site tracking technologies.
Privacy Policy
