Skip to content
WhatsApp
Request a Quote
Rivets · Trade series (GESIPA standard blind rivet studs)

A2 (304) Stainless Steel Blind Rivet Nut Studs

Mechanical properties, corrosion behaviour and the full dimensional range for this grade.

A2 Stainless Steel Blind Rivet Nut Studs are supplied to ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70. Corrosion behaviour is good general corrosion resistance, the material is largely non-magnetic, and the usable service range is approx. -200 °C to +400 °C, subject to the property class and the joint. In practice this grade is the most common stainless group for indoor and general outdoor fasteners.

Grade
ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70
Corrosion resistance
Good general corrosion resistance
Magnetic response
Largely non-magnetic
Service temperature
approx. -200 °C to +400 °C, subject to the property class and the joint

Property values are typical for the grade. Certified mechanical test data is available on request for production orders.

A2 (304) Stainless Steel Blind Rivet Nut Studs reference image

For blind rivet nut studs in A2 Stainless Steel, the controlling selection factors are corrosion exposure, strength requirement and service temperature. The grade data for A2 Stainless Steel (ISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70) is summarized below together with every size supplied.

Why Choose A2 Stainless Steel for Blind Rivet Nut Studs

The most common stainless group for indoor and general outdoor fasteners. For blind rivet nut studs, this matters when good general corrosion resistance is the primary requirement.

Mechanical & Physical Properties

Grade designationISO 3506 group A2 (304 / 1.4301), commonly supplied A2-70
Magnetic responseLargely non-magnetic
Service temperatureapprox. -200 °C to +400 °C, subject to the property class and the joint
Corrosion characteristicGood general corrosion resistance

Corrosion Behavior in Service

A2 (304) gives excellent atmospheric and most-water corrosion resistance and is the most common stainless for Blind Rivet Nut Studs in indoor and general outdoor service. In chloride-bearing environments (marine air, road salt, swimming pools) consider stepping up to A4 (316).

Galvanic & Galling Considerations

Two important notes for stainless blind rivet nut studs: (1) stainless can gall on stainless threads under load — use a thread lubricant or anti-galling compound, especially for M6 and below; (2) when joined to aluminum or galvanized steel, stainless can drive galvanic corrosion of the less-noble metal in wet service — isolate with a coating or sleeve where appropriate.

Using Stainless Fasteners in Aluminum

Stainless steel is more noble than aluminum, so in the presence of an electrolyte — rain, condensation, salt spray — the aluminum becomes the anode and corrodes at the joint. The effect is driven by the area ratio: a small stainless fastener in a large aluminum section is normally acceptable, while a large stainless fastener in thin aluminum is not. Where the joint is wet, isolate the two metals with a coated or nylon washer and a sealant, or specify an aluminum or coated fastener instead.

Sizes of Blind Rivet Nut Studs Available in A2 Stainless Steel

Thread sizeHead diameter (mm)Overall length (mm)Recommended hole diameter (mm)Body typeMaterial
M46126.10splined small-head blind body + projecting studsteel
M5711.57.10splined small-head blind body + projecting studsteel
M6915.59.10splined small-head blind body + projecting studsteel
M8111711.10splined small-head blind body + projecting studsteel

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

The form below follows the current technical drawing configuration. Change the drawing values above and the request details update automatically.

Request a Quotation

Specification
Business Information

Dimensions & Specifications (Trade series (GESIPA standard blind rivet studs))

Thread sizeHead diameter (mm)Overall length (mm)Recommended hole diameter (mm)Body typeMaterial
M46126.10splined small-head blind body + projecting studsteel
M5711.57.10splined small-head blind body + projecting studsteel
M6915.59.10splined small-head blind body + projecting studsteel
M8111711.10splined small-head blind body + projecting studsteel

Applications & Industries

The sectors that buy Blind Rivet Nut Studs, and the duty each one buys them for. Stocked from M4 to M8.

Industries that specify Blind Rivet Nut Studs

  • Automotive trim Blind studs for brackets where the back of the skin is inaccessible.
  • Electrical cabinets Stand-off and bracket attachment on closed sheet enclosures.
  • Rail interiors One-side threaded studs behind finished wall and ceiling panels.
  • Appliance panels Projecting threaded mounting points added after the housing is formed.
  • Transport & bodywork Trailer, bus and van panels joined blind from one side.
  • Signage & cladding Fast, vibration-resistant fixing of thin material.

Typical applications

  • holding a bracket on a closed section without a loose nut inside
  • selecting body hole and grip independently from the stud thread
  • using a blind-installed threaded point for repeat service removal
  • creating a projecting stud from the front side of sheet or tube
  • riveted pivots that must stay tight but still turn
  • permanent joints in thin sheet where a threaded fastener would loosen

Service conditions to specify against

Marine and coastal
Available in A4 (316) stainless for chloride exposure — coastal structures, pool halls, water treatment and deck hardware, where A2 will eventually pit.

Where to use something else

  • Do not size the panel hole from the stud thread; the blind body controls the recommended hole.
  • Not for a joint that has to come apart in service — removal means drilling the rivet out.

Full application guide: where Blind Rivet Nut Studs are used, how to specify them, and the cases they are wrong for

Inside the plant

Manufactured in our own plant

This part is cold-formed, threaded, heat-treated and finished in-house. The stages below are where its class and finish are actually decided.

  1. Wire rod feeding into a cold heading machine
    01

    Cold heading

    Wire rod is drawn to size and cold-formed into blanks. Forming rather than cutting keeps the grain flow continuous around the head, which is where a bolt is most likely to fail.

    Head dimensions and under-head radius checked at set-up and per shift.

  2. Thread rolling machine producing bolt threads
    02

    Thread rolling

    Threads are rolled between hardened dies rather than cut. Rolled threads are stronger in fatigue than cut threads and hold pitch and flank angle far more consistently across a batch.

    Go / no-go ring gauges to ISO 965 tolerance class 6g.

  3. Baskets of bolts staged for heat treatment
    03

    Heat treatment

    Quench-and-temper brings carbon and alloy steel to the property class ordered — 8.8, 10.9 or 12.9 — with the furnace charge tracked so a finished lot can be traced back to it.

    Core hardness and tensile tested per lot to ISO 898-1.

  4. Zinc plated bolts in a treatment basket
    04

    Surface treatment

    Zinc, zinc-nickel, hot-dip galvanizing, black oxide, phosphate and Dacromet, selected against the service environment rather than against the price list.

    Coating thickness and neutral salt spray hours to ISO 9227.

Frequently Asked Questions

Is A2 Stainless Steel food-grade?

A2 (304) is widely accepted for food contact in non-chloride environments; A4 (316) is preferred where chlorides are present.

Can A2 Stainless Steel Blind Rivet Nut Studs be used with aluminum?

Yes, but stainless drives mild galvanic corrosion of aluminum in wet service — isolate with a coating, sleeve or paint, or accept the trade-off if the joint is dry and indoor.

What's the service temperature limit for A2 Stainless Steel?

The practical service range is approx. -200 °C to +400 °C, subject to the property class and the joint.

Can A2 Stainless Steel replace plated alloy steel structurally?

Only at the standard strength classes — A2-70 / A4-80 are roughly equivalent to class 7 steel; A4-100 reaches class 8.8. For class 10.9 or 12.9 strength, plated alloy steel is required.

How do I request a quotation?

Use the technical drawing on this page to pick the exact configuration, then submit it with the quote form. We respond within one business day.